cement-based self-leveling underlayment
Combo VFloor1: 20kgs - Primer: 2kgs
VFloor1: 5kgs
Big bag 1000kgs
Primer Plastic tank 1000kgs
Description:
VFLOOR1 is a single component Cementitious Self Leveling Mortar. Once cured, it provides a smooth, level surface on which to install a variety of floor coverings.
Suitable for prepairing interior floors prior to laying parquet, vinyl sheet and tile, soft floor covering, natural stone, ceramic tiles, etc…
It can be used on a wide range of absorbent and non-absorbent floor surfaces including concrete, cement and sand screeds, terrazzo, asphalt, ceramic & quarry tiles.
Layer-thickness 2-10mm
Can be pumped
Standard primers give excellent bonding to the VFLOOR1 products
Product name |
VFLOOR1 |
Compressive strength |
>40 Mpa, 28 days later |
Flexural strength |
>8 Mpa, 28 days later |
Application temperature |
5-30 degree |
Mixing ratio |
20kgs powder + 5.2kgs Liquid |
Product name |
PRIMER |
Mixing ratio |
2kgs Primer + 2L water + 4kgs cement |
Feature & Benefits:
- Single component, just mix with water
- Good adhesion to primed substrates
- Good flow, self smoothing
- Rapid setting and early strength
- Easy and quick to lay
Installation System:
Direction for use:
Mixing:
Add clean water to suitable mixing bucket. Mix slowly and continuously to form a homogeneous mixture.
- VFLOOR1 20kgs barrel required approximately 5.2 litres of clean water
- VFLOOR1 5kgs barrel required approximately 1.3 litres of clean water
The mixed materials is immediately ready to use and should be used within 30-40 minutes after mixing.
Ready for foot traffic after approx. 3 hours.
Laying:
Pour the mixed material onto the floor immediately after mixing and spread with wide sweeping strokes using a plaster’s plastic or steel float.
Use firm pressure and work well into the corners and around projections.
Leave a neat edge for subsequent batches.
Subsequent mixes should be poured into the wet edges of the previous mix.
Old partially set material must be scraped and discarded
Hardening:
Full strength is achieved after 28 days. At 28ºC room temperature, VFLOOR1 will be sufficiently dry to allow adhesive spreading after 48 hours.
This will take longer in colder climatic conditions. Do not lay in temperature below 5ºC
Under floor heating must be turned off at least 48 hours before work starts and left off until 48 hours after the final surfacing has been completed.
Drying time:
Prevent draughts across the floor to avoid localized premature drying
At ambient temperature, VFLOOR1 will appear to be dry after approximately 24 hours.
Floor laying may commence after 48 hours.
Safety Data:
As with all chemical products, care should be taken during use and storage to avoid contact with eye, mouth, skin and foodstuff (which can also be tainted with vapour until the product is fully cured or dried)
User Notes:
The technical details and recommendations contained in this data sheet are given in good faith and represent the best of our knowledge and experience at time of printing. It is the responsibility of the user to ensure that the products are used in accordance with VFLOOR1 instruction.
Construction:
Coverage:
- At an application thickness of 2mm the coverage will be approx. 5-6 m2 per 20kgs
- At an application thickness of 2mm the coverage will be approx. 1-1.5 m2 per 5kgs
Shelf Life:
18 months.
Packaging:
Combo VFloor1: 20kgs - Primer: 2kgs
Big Combo VFloor1: Big bag 1000kgs - Primer: 100kgs
VFloor1: 5kgs
>> CLICK TO SEE PRODUCT PRICE <<